You’ve just finished using your Intex hot tub and it’s time to deflate it. But how to deflate an Intex hot tub quickly and easily?
In this article, we’ll show you the best way to deflate your Intex hot tub. We’ll also share some tips on how to store it properly, so you can enjoy it for years to come.
Why and When You Should Deflate Your Intex Hot Tub
You should deflate your Intex hot tub when you’re not using it.
It’s as simple as that. If you leave the hot tub inflated, it will slowly lose air and eventually collapse. Not only is this a pain to deal with, but it can also damage the hot tub.
So if you’re not using your hot tub, remember to deflate it! It’ll save you a lot of hassle in the long run.
Before Deflation: Getting Your Hot Tub Ready for Deflation
Now that you know how to deflate your Intex hot tub in a hurry, it’s important to take a few minutes and do some prep work before you start. This will make the process go a lot smoother and faster.
The first step is to remove the hot tub’s cover. This will give you easier access to the valves and make it less likely for the cover to get damaged in the process.
Once the cover is off, locate the deflation valves. There are usually two of them, one on each side of the hot tub. They’re usually a screw-type valve, so you’ll need a screwdriver to open them.
If your hot tub has an air pump, make sure it’s turned off and unplugged from the electrical outlet before you start deflating it. This will help avoid any accidents or injuries.
Now that everything is ready, start deflating your hot tub by opening the deflation valves. Most of the air will come out quickly, but there may be a little bit left in the bladder. If this happens, just use a pump or broomstick to push it out. Once all the air is out, fold up the hot tub’s cover and store it somewhere safe until next time.
8 Steps on how to deflate intex hot tub
The intex hot tub is a great way to relax and enjoy your time in the pool. However, it can be dangerous if you don’t know how to deflate the tub properly. If the hot tub isn’t properly inflated or maintained then it could lead to problems with your health and safety. In this article we’ll show you steps on how to deflate an intex hot tub so that it’s ready for storage when not in use!
Remove the pump and hose
Remove the pump and hose from the hot tub’s drain valve. The best way to do this is by unscrewing it from its mounting bracket, then pulling it out of the drain valve hole in your hot tub.
You’ll need a wrench or pliers to loosen up any clamps holding down your pump’s wires so they can be pulled out without breaking them off at their connection points on your pump itself (e.g., if you have an older model Intex PowerSpa with no built-in electrical cord). If there are any other connections between these parts—like tubing—you’ll also want someone who knows how these things work so they can make sure everything comes free nicely without damaging anything else along with it!
Remove the filter cartridge
This is a very important step on how to deflate intex hot tub. The filter cartridge is located at the bottom of your hot tub and it’s where you’ll find all the dirt, debris, and oils that collect during use. To clean this area thoroughly, remove it from its housing by removing one screw on either side (it’s usually just held in place with a single screw).
Once you’ve removed this part of your hot tub filter system, use a hose to spray water into it until all build-up has been removed from inside. Then replace everything back together so that your new filter is installed properly—and don’t forget to put some kind of protective covering over any exposed wires!
Unscrew the drain cap
The drain cap is located on the bottom side of your hot tub and it has a rubber seal. It’s a small screw cap with another larger one over top of it, which you can use to help remove it from your tub.
To unscrew this cap, you’ll need to use a screwdriver or other tool to pry up on one end while simultaneously pressing down on its opposite end (you’ll see why later). Once that’s done, take out any debris that may have been lodged inside by flipping open both pieces so they’re facing each other again and then pulling them apart gently enough so as not break anything important like tiny springs inside them (or worse yet–a piece if plastic!).
Open the drain cap located on the bottom side of the tub
The first step to deflating an intex hot tub is opening the drain cap located on the bottom side of your tub. To do this, you will need an appropriate sized screwdriver or wrench and make sure that there isn’t any water in your hot tub before opening it.
If you don’t know how to remove or open this drain cap then call customer service at 1-800-INTEX-USA (1-800-446-4837) for assistance!
Drain hot tub completely
Drain the hot tub completely. Clean the filter before storing it. Store in a dry place away from sharp objects, such as glass and metal pipes, which could damage the cover or inflate your hot tub when punctured by them.
Here’s another vital step on how to deflate intex hot tub. The intex hot tub is equipped with a drain valve and a cold water inlet valve. Open both of these valves to drain out any excess water from your hot tub. Then open the hot water inlet valve to allow more air into the spa, which will help deflate it faster.
Fold up and store your hot tub properly
Store it in a safe place. If you can’t fold it up and store it, then put the cover on top of the tub and keep it somewhere out of reach until you can move the hot tub to its new location.
Don’t leave anything sharp near your inflatable pool – this includes jewelry, glassware and other breakable items! Sharp objects could puncture holes in your pool’s material or cause injury if they hit someone on accident. Also make sure there’s no water inside when taking apart an inflatable pool because any leaks could lead to damage later on down the road (like being damaged by bugs).
Keep away from direct sunlight or heat sources like fireplaces during storage periods as these could melt plastic parts over time leading potentially causing leaks or other issues down line which may require expensive repairs later down line–so please don’t try this at home!
Keep the cover away from any sharp objects and always keep it clean
The cover of your hot tub is the most important part of maintaining your tub. It’s also the most vulnerable and can be easily damaged if you don’t take proper care of it.
- To keep your cover in good condition, follow these steps:
- Always use a soft cloth or towel to clean the surface of your intex hot tub cover because harsh chemicals can damage it over time.
- Don’t leave any moisture on top of this product for long periods of time as this may lead to mold growth inside its bodywork.
- Do not use bleach or other strong cleaning agents when cleaning this item because some materials may cause discoloration on surfaces such as vinyls or fabrics (such as leatherette).
Tips for Maximizing Water Drainage to Help Deflate the Hot Tub Quickly
When it comes time know how to deflate intex hot tub, it’s important to maximize the water drainage so the process goes as quickly and easily as possible. Here are some tips to help:
Make sure the cover is off and all the water is drained before deflating. This will help reduce the amount of time it takes to release all the air.
If there’s a pool pump available, use it to speed up the deflation process.
Poke holes in the side of the hot tub near the bottom. This will help release trapped air more quickly.
Once most of the air has been released, grab onto the deflated tub and give it a good shake. This will help get rid of any remaining air pockets.
After Deflation: How to Properly Store Your Intex Hot Tub
Once you have finished deflating your Intex Hot Tub, it is vital to think about how to store the hot tub until its next use. If properly stored and cared for, an Intex Hot Tub can last for many years.
If you plan to keep your hot tub outdoors, ensure that it’s placed in a flat area and protected from the elements, such as wind and rain. Otherwise, a cover should be installed over the top of the hot tub. After each use, make sure to empty out any water inside and clean out the filter. Lastly, don’t forget to dry out your Intex Hot Tub before putting it away!
If you are planning on storing your hot tub indoors for extended periods of time—e.g. winter—make sure the area is completely dry and warm enough that condensation does not occur inside the unit.
Additionally, refrain from using any harsh chemicals or detergents when cleaning your Intex hit tub. Instead opt for something mild such as baby shampoo or a mild dish soap suds solution. The key is to make sure that when storing your Intex Hot Tub, no moisture or moisture barrier can penetrate its housing so that it remains in peak condition for years to come!
FAQs on how to deflate intex hot tub
Maybe you still have questions about how to properly deflating Intex hot tub. Here are some common questions and answers that may help:
Can I use a pump to deflate my Intex hot tub?
Yes, you can use an electric or battery-operated pump to remove the air from the Intex hot tub. However, make sure to follow the manufacturer’s instructions for correct operation.
Is it okay to use a vacuum cleaner?
Yes, using a vacuum cleaner is an easy and efficient way to deflate an Intex hot tub. Just be mindful that some vacuums don’t have enough suction power to do the job quickly.
How long does it take to deflate an Intex hot tub?
Generally speaking, it should take about 15 minutes for an electric pump and about 30 minutes for a vacuum cleaner. Time can vary depending on the size of your hot tub and the efficiency of your device.
So there you have it, a few steps on how to deflate intex hot tub quickly and easily. So the next time you want to take a break from your hot tub, you’ll know just what to do!