Soaker Tub With Shower Buying Guide

soaker tub shower

If you’re looking to improve your bathroom’s bathing experience, a soaker tub with shower might be the perfect solution. There are a few factors to consider before choosing this type of bathtub, including cost, size, and materials. You may also want to think about installation. Listed below are some tips to help you make a decision. After reading this article, you’ll be well-equipped to make an informed purchase.

The cost of buying:

If you’re looking for a tub with a shower, you’ve probably wondered how much it costs. While some bathtubs have lifetime warranties, many do not. If they do, the warranty may not cover labor or random parts. 

And you’ll probably have to pay for the caulking after two years. So if you’re unsure of what size bathtub you want, try reading the buying guide first.

Check this out:

[amazon box=B07HKJM89G]

Spirit is a decent choice in most areas, but you should pay attention to its warranty. While the company says that it stands behind its products, you shouldn’t expect them to do the same. You should never expect a free product, and it’s important to research the warranty as well. 

Ariel’s warranty is the least transparent, but it’s still worth considering. You can also find out if you’ll have to pay additional fees if you’re not satisfied.

Size of soaker tub with shower:

soaker tub shower
Source: STS

If you want to enjoy the benefits of a soaker tub with a shower, you should know that its dimensions vary widely. Freestanding bathtubs generally range in width from 20 to 59 inches. 

The average soaking depth is about 15 inches, while Japanese tubs are even deeper, reaching 35 inches. To choose the right size for your bathroom, consider how much space you have available in the area. If you have a small bathroom, a freestanding tub can be a good fit.

While freestanding bathtubs usually have a depth of 14 to 20 inches, deeper bathtubs are usually more shallow. 

Some models are 20 inches tall, but only hold 13 inches of water. The best way to determine the ideal soaking depth for you is to take measurements from the same spot on both sides and ends. You can use a tape measure to make accurate measurements. Once you know the size of your tub, you can start shopping.


There are many materials you can choose from when installing a soaker tub with shower in your bathroom. You can choose from acrylic, fiberglass, and cast iron. Fiberglass tubs are made by forming layers of fiberglass into the desired shape and covering them with a resin called Gelcoat. 

These materials are extremely durable, easy to clean, and can be very attractive to look at. But beware that these materials can be expensive and can be damaged easily.

For an extra-luxurious look, you can choose a stone resin bathtub. The resin will not wear down or discolor after many years of use, unlike fiberglass or acrylic. It will last for a long time and will be made entirely out of recycled material. 

A stone resin bathtub is a luxury purchase, as it is easy to clean. Mildew and other residues will come off with warm water and a mildew remover. If you have a particularly stubborn residue, you can try abrasive substances to clean it.


Before installing a soaker tub with shower, it is important to understand how to properly frame the area for the new bathtub. If the tub will be mounted on a recessed nook, the flange should be set into studs. If the tub will be mounted on a drywall surface, the flange should be secured with screws. 

The surrounding area should be insulated. If the bathtub will be placed on the floor, you must support it along its entire bottom. A bed of mortar should be applied along the entire area and across each point of contact with the drywall. The depth of the mortar bed depends on the distance between the tub bottom and the floor.

The back surround panel must be installed first, followed by the side panels. Then, chisel off any protruding studs. 

Make sure to cut the drywall to the desired dimensions. Set the new shower valve, if applicable, and the copper lines. Reset the back panel to the center of the spout. Remember to measure twice before cutting it. You can use a hole saw or a jigsaw to make clean cuts.

Leave a Reply

Your email address will not be published. Required fields are marked *